Audi A4 B8 - What are the most common problems and breakdowns of the Audi A4 B8

Audi A4 B8

Audi A4 B8

What are the most common problems and failures of the Audi A4 B8 and how to solve them?

Audi A4 B8 - All models with automatic rear door opening / closing, → 11/09.
PROBLEM - The automatic closing of the rear door does not work. Error codes related to the electric rear door are stored in the error memory.
CAUSE - Multifunction control module software error.
REPAIR - Perform component, electronics, and mechanical tests (as needed) to eliminate other possible causes. If no error is found: Reprogram the multifunction control module with the updated software.

Audi A4 B8 - All models
PROBLEM - The rear window heater does not work.
CAUSE - Multifunction control module software error.
REPAIR - Perform component, electronics, and mechanical tests (as needed) to eliminate other possible causes. If no error is found: Reprogram the multifunction control module with the updated software.

Audi A4 B8 - All models with keyless entry.
PROBLEM - Occasional automatic activation of the alarm system siren. Error codes related to the keyless entry system sensor are stored in the error memory. Error codes related to the alarm system are stored in the error memory.
CAUSE - Defective keyless entry sensor (s).
REPAIR - Perform component, electronics, and mechanical tests (as needed) to eliminate other possible causes. If no error is found: Install the modified keyless entry system sensors.

Audi A4 B8 - All models with parking assist control, 2003 →.
PROBLEM - Parking assist warning devices activated without interference.
CAUSE - Unfurnished parking assist provider (s). Parking Assist (s) Contaminated by Corrosion or Dirt. Improperly installed front license plate bracket.
REPAIR - Check error codes. Make repairs if necessary. Check for damaged, contaminated, or improperly installed parking assist encoders. Replace / repair parts as needed. Check that the front license plate bracket is installed correctly.

Audi A4 B8  2.7D TDI CR
PROBLEM - Bad cold start. Startup error. Possible stored error codes: P161A, P161B, P161C, P161D, P161E, P161F, P161G, P161H.
CAUSE - Defective heaters
REPAIR - If fault code (s) is present, install new heaters.

Audi A4 B8 3.2 FSi
PROBLEM - Unusual noise from the engine coolant pump space at idle.
CAUSE - Air in the cooling system.
REPAIR - Bleed the cooling system several times.
Start the engine. If noise is still present: Replace the engine coolant pump.

Audi A4 B8 3.2 FSi 2009.
PROBLEM - Indicator light Engine Malfunction (MIL) illuminates. Possible stored error codes: P0016, P0017, P0018, P0019. Small loss of engine power.
CAUSE - Camshaft Position (CMP) Sensor and Intake Camshaft Camshaft Adjustment on Cylinder Group 1. Contamination of the camshaft position (CMP) actuator and mechanism.
REPAIR - If error code P0016 is present: Check the camshaft position (CMP) and camshaft camshaft relay settings on cylinder group 1. If the reference marks are not aligned, replace the camshaft. If the camshaft position (CMP) relay is camshaft camshaft on cylinder group 1 aligned, remove the appropriate camshaft position actuator (CMP) and check for contamination. Clean the camshaft position (CMP) actuator and actuator housing if necessary.
If present error code P0017: Remove the Camshaft Position Actuator (CMP) of the exhaust valves on cylinder group 1 and check for contamination. Clean the camshaft position actuator (CMP) and actuator housing if necessary.
If present error code P0018: Remove the Camshaft Position Actuator (CMP) of the intake valves on cylinder group 2 and check for contamination. Clean the camshaft position actuator (CMP) and actuator housing if necessary.
If present error code P0019: Remove the Camshaft Position Actuator (CMP) of the exhaust valves on cylinder group 2 and check for contamination. Clean the camshaft position actuator (CMP) and actuator housing if necessary.
Delete the error codes from the ECM error memory.

Source: autoportal.hr


Leave a reply